>>This is a DIGITAL DOWNLOAD | No product will be shipped | After checkout you will be provided the link to download your files. <<
File Type: STL and 3MF
3D MODEL DESCRIPTION
Skeleton bands only have groupies because their fans have no-body to watch the shows with.
Assembling Instructions:
- Take GEAR_1 and tighten the spring with your fingers as shown in the video, and place it inside BODY, fitting the outer hole of the spring onto the pin inside BODY.
- Fit GEAR_3 onto GEAR_2 and attach it on top of GEAR_1 so that GEAR_3 is facing downwards.
- From the outside, thread GEAR_8 so that the pin goes through the holes of the aligned gears on the inside.
- Attach GEAR_4 onto the pin of BODY.
- Attach GEAR_5 onto the top of GEAR_3, through the pin of GEAR_8.
- Place GEAR_6 on top of GEAR_4.
- Fit CHEST_PLATE on top of everything, aligning the pins with the holes and the slots on the side, as shown in the video.
- Put GEAR_7 over CHEST_PLATE, fitting it onto the first pin.
- Attach CHEST_ELIPSE so that the inner diameter touches GEAR_7, as shown in the video.
- Fit CHEST_ELIPSE_SLIDER below CHEST_ELIPSE, in its designated space.
-
Finish by attaching and gluing the remaining parts
- This STL file is recommended for FDM Printers!
- Approximately Height: 28cm
3D PRINT FILE SETTINGS (FOR 0.4 MM NOZZLE)
- Line Width/ Nozzle: 0.4 mm
- Average Speed: 20mm/s (First Layer) / 50mm/s (All the other layers)
- Recommended Initial Layer Height: 0.12 mm
- Recommended Layer Height: 0.12 mm
- Recommended Perimeters/ Walls: 3.
- Recommended Infill (%): 10% (Gyroid)
- Needs Support: No.
- Build Plate Adhesion: None.
The parameters above are recommendations made by our staff; if you prefer, you can adapt them according to your preferences.
| Shipping | This item ships to |
Description
>>This is a DIGITAL DOWNLOAD | No product will be shipped | After checkout you will be provided the link to download your files. <<
File Type: STL and 3MF
3D MODEL DESCRIPTION
Skeleton bands only have groupies because their fans have no-body to watch the shows with.
Assembling Instructions:
- Take GEAR_1 and tighten the spring with your fingers as shown in the video, and place it inside BODY, fitting the outer hole of the spring onto the pin inside BODY.
- Fit GEAR_3 onto GEAR_2 and attach it on top of GEAR_1 so that GEAR_3 is facing downwards.
- From the outside, thread GEAR_8 so that the pin goes through the holes of the aligned gears on the inside.
- Attach GEAR_4 onto the pin of BODY.
- Attach GEAR_5 onto the top of GEAR_3, through the pin of GEAR_8.
- Place GEAR_6 on top of GEAR_4.
- Fit CHEST_PLATE on top of everything, aligning the pins with the holes and the slots on the side, as shown in the video.
- Put GEAR_7 over CHEST_PLATE, fitting it onto the first pin.
- Attach CHEST_ELIPSE so that the inner diameter touches GEAR_7, as shown in the video.
- Fit CHEST_ELIPSE_SLIDER below CHEST_ELIPSE, in its designated space.
-
Finish by attaching and gluing the remaining parts
- This STL file is recommended for FDM Printers!
- Approximately Height: 28cm
3D PRINT FILE SETTINGS (FOR 0.4 MM NOZZLE)
- Line Width/ Nozzle: 0.4 mm
- Average Speed: 20mm/s (First Layer) / 50mm/s (All the other layers)
- Recommended Initial Layer Height: 0.12 mm
- Recommended Layer Height: 0.12 mm
- Recommended Perimeters/ Walls: 3.
- Recommended Infill (%): 10% (Gyroid)
- Needs Support: No.
- Build Plate Adhesion: None.
The parameters above are recommendations made by our staff; if you prefer, you can adapt them according to your preferences.
Shipping
| Shipping | This item ships to |
Related Products
Recently viewed products
